SQ ADSRs

Set to 1 if all MDSRs corresponding to this ADSR are blank, set to zero otherwise. This flag will always be zero because this ADSR is updated once per slice or scene. Therefore, if there are no MDSRs, this ADSR is not produced at all.

0 = mean of I and Q input values are both within specified range from expected mean. For expected mean of x, the measured mean must fall between x-threshold to x+threshold. 1 = otherwise

0 = standard deviation values of I and Q input values are both within specified range of expected standard deviation. For expected std. dev. x, the measured std. dev. must fall between x-threshold to x+threshold. 1 = otherwise

0 = number of input gaps <= threshold value 1 = number of input data gaps > threshold value.

0 = percentage of missing lines <= threshold value 1 = percentage of missing lines > threshold value. The number of missing lines is the number of lines missing from the input data, excluding data gaps.

0 = confidence measure >= specified value 1 = confidence measure < specified value. If more than one Doppler centroid estimation is performed in a slice, the flag is set if any confidence measure is less than the threshold.

0 = confidence measure >= specified value 1 = confidence measure < specified value

0 = mean of I and Q output values for SLC image or mean of detected pixels for a detected product, are both within specified range from expected mean. For expected mean of x, the measured mean must fall between x-threshold to x+threshold. 1= otherwise.

0 = mean of I and Q output values for SLC image or mean of detected pixels for a detected product, are both within specified range from expected mean. For expected mean of x, the measured mean must fall between x-threshold to x+threshold. 1 = otherwise

0 = able to reconstruct all chirps or chirp reconstruction not requested (nominal chirp used) AND all quality measures were acceptable. 1 = unable to reconstruct a chirp during processing and chirp reconstruction was requested or the quality is below the acceptable levels. When value = 1, (i.e. unable to reconstruct a chirp during processing and chirp reconstruction was requested or the quality is below the acceptable levels), PF-ASAR uses the nominal range pulse for processing and a nominal elevation beam scaling factor.

0 = all data sets which are supposed to be in the product are present 1 = any data sets (including ADSs) are missing from the product which are supposed to be included under normal circumstances. When value = 1 (i.e any data sets, including ADSs, are missing from the product which are supposed to be included under normal circumstances), which data sets are missing can be determined by an examination of the DSDs in the SPH.

0 = all parameters read from the downlinked data were valid 1 = displayed if any downlink parameter is out of range and therefore a default value has been used during processing.

Maximum percentage broadening permitted in cross-correlation pulse width compared to theoretical width.

First sidelobe of the chirp cross correlation function

ISLR of the chirp cross correlation function

For an expected mean value of x, this is the value T, such that the measured mean must fall between the x-T and x+T.

For an expected standard deviation value of y, this is the value D, such that the measured standard deviation must fall between the y-D and y+D.

Threshold for Doppler Centroid confidence

Threshold for setting the Doppler Centroid ambiguity confidence flag

For an expected mean value of x, this is the value T, such that the measured mean must fall between the x-T and x+T.

For an expected standard deviation value of y, this is the value D, such that the measured standard deviation must fall between the y-D and y+D.

Maximum percentage of missing lines to total lines.

Maximum number of missing gaps allowed.

I channel, Q channel

I channel, Q channel

Composed of a predetermined number of consecutive missing lines

Excluding gaps

For detected products: second value is set to zero, or I channel followed by Q channel for SLC

For detected products: second value is set to zero, or I channel followed by Q channel for SLC

0 = no land in imagette 1 = land in imagette

1 = The ratio of the standard deviation to the mean of the first look image is outside the range given by a minimum and a maximum threshold. 0 =otherwise

1 = The normalised deviation of the two inter-look sub-images is greater than a maximum threshold. 0 = otherwise

1 = The normalised RMS error between the fitted co-variance profile is greater than a maximum threshold. 0 = otherwise

1 = The Azimuth cut-off fit did not converge within a minimum number of iterations. 0 = otherwise

1 = The imaginary spectral peak is less than a minimum threshold, and the zero lag shift is greater than a minimum threshold. 0 = otherwise

The ratio of the standard deviation to the mean of the first look image.

The normalised RMS error between the fitted co-variance profile.